No products
High-quality replacement gudgeon pin circlips from Malossi for 10mm and...
The HAT weights are very durable and self lubricating. Available in a...
Pro Taper is well known for manufacturing high-quality grips and...
Budget weights by Motoforce, choice of weights. Available in a range of...
Replacement reed valve gasket for all Minarelli Horizontal engines.
The thermal grade of the spark-plug is of prime importance with tuning...
We can offer high-quality exhaust gaskets for all common original, sport...
The Polini FOR RACE crankshafts are developed to increase the...
The Polini FOR RACE crankshafts are developed to increase the...
Ready to bring your bike into a class...
Reference: SCT-HCCP1232
Brand: Ruckhouse
These are for our 4/110 wheels. They sandwich between the wheel and your hub for the perfect fit. You won’t be losing this baby down the street. The flange on the outside is only .075 thick so don’t worry about your wheel not lining up. It will probably help line it up better since most mounts on the market hold your engine too far to the left.
Reference: SCT-164-30
Brand: Scootertuning.ca
Rear axle nut for GY6 125-150cc Short/Long wheel axle.
Reference: S802-343/AL
Brand: Ruckhouse
Looking to run a fatty rim on a Honda ruckus with GY6 motor? here's the hub you need. The hub has 4x102, 4x110 & 4x130 bolt pattern that allow to use lot's of Douglas & Aftermaket 12x8 / 12x7 wheels. 4x102 Bolt pattern is already including studs. We recommend our lug nuts to install the wheel. 4x110 and 4x130 Can be used with Regular M10 bolts or...
Reference: RH-173
Brand: Ruckhouse
Complete Front Hub for Honda Ruckus with Ruckhouse brake disc adaptor. Installation Note: When putting the center axle, some of these are not fitting due to the center bar inside the hub being a hair too small. Hitting the axle with a hammer will knock out bearing. Remove center piece and reinstall bearing. This piece is not needed anyways.
Reference: 1000-1263.10
Brand: NCY
Electroplated front wheel axle by NCY for Ruckus. . Has safety wire / cotter pin provisions (2mm)! Dimension : 12mm X 250mm. Attention, does not fit OEM forks!
Reference: 1000-1131.1
Brand: NCY
High quality electroplated rear axle nut by NCY for GY6 engines.
Reference: RH-170
Brand: Ruckhouse
Professional Crafted front Billet Hub for 4x90 pattern front wheels with Brake Adapter flange, 3 NCY Titanium finish rotor bolt and 3 Stainless bolts to attach Brake disc adapter plate.
Reference: TRS-ASK
Brand: TRS
This axle spacer kit is to center wheel with aftermarket front hub normally used with Douglas, TRS or other Ruckus wheels. You may have to add (using washer) or remove (file) a couple thousanth off the spacer as we have no control over how far the manufacturer presses the bearing in the hub.
Reference: GY16640
Brand: Scootertuning.ca
Gearbox output shaft (wheel shaft) for GY6 125/150cc 4-stroke Chinese-built engines. This version is for vehicles with a rear drum brake. Shaft length 135mm.
Reference: SCHS-203
Brand: Ruckhouse
Set of 4 socket screws, Zinc plated grade 12.9 for a rear Fatty wheel combined with a Rear Hub Multi Bolt partern (4x100, 4x110, 4x130).
Reference: RH-041
Brand: Ruckhouse
Stop running car lug nut on a Flat Douglas or Custom Ruckus wheel! They do not allow proper tightening due to lack of surface area and over time they will wallow out the wheel holes. We got the fix!! Our lug nuts are flat for proper surface area on most flat wheels such as Douglas or any of our wheel sets. These are M12x 1.5 thread pitch please check your...
Reference: RH-042
Brand: Ruckhouse
Reference: RH-043
Brand: Ruckhouse
Reference: RH-044
Brand: Ruckhouse
Reference: RH-045
Brand: Ruckhouse
Reference: RH-047
Brand: Ruckhouse
Reference: RH-048
Brand: Ruckhouse
Reference: RH-174
Brand: Ruckhouse
Professional Crafted front Billet Hub for 4x90 pattern front wheels with Brake Adapter flange, 3 NCY Titanium finish rotor bolt and Stainless bolts to attach Brake disc adapter plate.
Reference: RH-188
Brand: Ruckhouse
These lugs allow you to run our M12x1.5 Flat Lug Nuts with a Gy6 Rear Hub with M10x1.5 bolt hole. No need to drill and tap your hub or open the hole on your wheel . Most wheel come with M10 holes not M12 . Put wheel on with these, insert washer then Flat Lug Nut and you now have the look of Lugs without any mods. We recommend Red Loctite on both hub and...
Reference: FLP-013
Brand: FLP
Safely mount your custom 1 piece wheels and use off the shelf metric lug nuts and have them seat up properly. Don’t risk you lug nuts coming loose with minimal surface contact on your flat faces wheels. Specs : 4 pieces 6061 washers, Made for M12 stud, 60 degree taper to fit all metric lug nuts.
Reference: FLP-014
Brand: FLP
Safely mount your custom 1 piece wheels and use off the shelf metric lug nuts and have them seat up properly. Don’t risk you lug nuts coming loose with minimal surface contact on your flat faces wheels. Specs : 4 pieces 6061 washers, Made for M12 stud, 60 degree taper to fit all metric lug nuts.
Reference: FLP-017
Brand: FLP
So you are ready to add new wheels to your ruckus BUT you don’t want to fork out 1000.00 dollars to get a full disk brake set up. This is where our Front Drum Hub comes in. BOLT ON 12 x 4 4X90 or 5x90 wheels. 100 percent bolt on. Speedometer still works. Wheel bolts included. Use you factory wheel spacer. THINGS TO KEEP IN MIND : These only work with the...
Reference: S802-343/BK
Brand: Ruckhouse
Looking to run a fatty rim on a Honda ruckus with GY6 motor? here's the hub you need. The hub has 4x102, 4x110 & 4x130 bolt pattern that allow to use lot's of Douglas & Aftermaket 12x8 / 12x7 wheels. 4x102 Bolt pattern is already including studs. We recommend our lug nuts to install the wheel. 4X110 and 4x130 Can be used with Regular M10 bolts or our M10...
Reference: RH-204
Brand: Ruckhouse
Reference: RH-210
Brand: Ruckhouse
Replacement hub adaptor for the wheel hub v2 TRS